Moving USDT between an exchange and a wallet comes down to two pages: the receiver's deposit page sets the network and the address, the sender's withdrawal page must use the network with the same name, and contract and memo get one last check before you confirm. The checks below come from the official help pages of OKX and Tether Wallet and apply on any chain. If the checks land on TRC20 and you send from your own TRON wallet, consider GasStation to rent Energy for the sending address first, because a TRC20 transfer consumes Energy and GasStation needs only the address, delivering by native TRON delegation. If you withdraw straight from an exchange account, follow the fee shown on its withdrawal page. For the overall choice of network, see the main guide to choosing a USDT transfer network.
A GasStation Quick Rental order asks for the target address that receives Energy, and an exchange deposit page follows the same order: pick the network, then copy the address issued for it. OKX's help centre walks through it: select Deposit crypto, choose the asset, choose the deposit network, copy the deposit address, then paste it under Withdraw on the other platform or wallet.
OKX adds that for most cryptocurrencies it selects the network automatically, and for some it asks you to choose. When you do choose, the list is the range the receiver accepts; copy the address only after the network is set, and copy again if you switch networks.
GasStation is concerned only with the TRON network, which exchange pages often label TRC20, Tron or USDT-Tron (TRC20); other networks carry aliases too, so match the network itself rather than the wording. OKX gives two examples:
BEP20, BSC and Binance Smart Chain are all referred to as BNB Smart Chain on OKX.
USDG-ERC20 on one side means USDG-ERC20 on the other: the withdrawal network must equal the deposit network, whatever each platform calls it.
The same help centre notes that each network differs in speed, security and transaction fee, much as different modes of transport do.
This checklist comes from Tether Wallet's help pages and applies equally to GasStation users sending on TRC20. Tether Wallet's guide asks you to select the relevant network and then double-check that these details match the other party:
1. Currency: USDT on both sides. 2. Contract: if unsure, read the token page and check the blockchain contract address before sending. 3. Blockchain: match the network using the name mapping above. 4. Layer: scaling networks sit alongside a main chain, so both ends must be on the same layer. 5. Memos or tags: fill them in whenever the receiver requires one.
Energy delegated by GasStation stays on the address you entered, and an exchange withdrawal is just as one-way, so every check belongs before you press confirm. OKX's withdrawal guidance states that once a withdrawal shows In Progress or Transferred Out, it cannot be cancelled on OKX; the assets have left the platform, and the receiving platform or wallet is the one to contact.
Arrival depends on two things: the network's own confirmation speed and the number of block confirmations the receiving platform requires. OKX notes that the Ethereum network can slow down when busy, and that platforms set different confirmation counts, so credited funds may lag behind the transfer. Checked on 20 October 2026.
Disclaimer: the same OKX page states that a network mismatch results in withdrawal failure even when the token is USDT on both ends, and that a USDT withdrawal should use only networks the receiver lists, even when another network is cheaper.
When you send USDT from your own TRON wallet to a receiver's TRC20 address, consider GasStation to rent Energy for the sending address first, because a TRC20 transfer consumes Energy. Take the network and address from the receiver's deposit page, select the same name on the withdrawal page and check currency, contract, blockchain, layer and memo; exchange withdrawals follow the fee on the withdrawal page.
The receiver's listed network comes before the fee. OKX notes that some platforms or wallets are incompatible with the TON or X Layer networks, so a USDT withdrawal should use a network the receiver lists even when those two are cheaper. Confirm on the receiver's deposit page first, then compare fees.
Once the status reads Transferred Out, the assets have left the sending platform, and arrival depends on network confirmation speed and the receiver's required confirmations. Look the transaction up on a block explorer; if it has enough confirmations and is still not credited, contact the receiving platform with the transaction hash.
OKX selects the network automatically for most assets, but that is only the sending side's default. When the receiver is another platform, open its deposit page and compare the listed network with the one selected for you; copy the address if the names match, and change the selection if they differ.
Service note: GasStation's site states that it provides blockchain resource technology services only and does not constitute any form of investment, financial product or return guarantee; users should assess the risks of using the TRON network and related services and comply with the laws of their jurisdiction.